MNRE Proposes Revised ALMM List-II Solar Cell Naming System in 2026
MNRE proposes a 14-character ALMM List-II solar cell naming system. Check technology codes, origin rules, transition plans and manufacturer impact.
Schedule a Call Back
Introduction
The proposal, issued through an Office Memorandum dated 5 October 2026, aims to make solar cell identification more consistent across manufacturers.
Under the proposed system, every enlisted solar cell model would carry the manufacturer's brand name followed by a 14-character alphanumeric identification code. This code would provide information about where the cell's main materials were produced, the technology used, wafer size and cell efficiency.
Currently, manufacturers use their own model naming methods. As a result, the names do not always provide a consistent way to identify and compare the technical characteristics of solar cells.
MNRE has revised its earlier August 2026 proposal after examining stakeholder comments. The revised draft is now open for further suggestions until 12 October 2026.
For solar PV cell manufacturers, module producers and suppliers, the proposal could mean changes to model identification and related technical records. However, the revised naming system is still a draft proposal and should not be treated as an implemented requirement.
Notification at a Glance
| Particular | Details |
| Issuing authority | Ministry of New and Renewable Energy (MNRE) |
| Document type | Office Memorandum- Revised Draft |
| File number | 283/59/2026-GRID SOLAR |
| Document date | 5 October 2026 |
| MNRE website listing date | 6 October 2026 |
| Subject | Standardised nomenclature for Solar PV Cell Models under ALMM List-II |
| Earlier proposal |
3 August 2026 |
| Main proposal | Manufacturer brand name followed by a 14-character alphanumeric code |
| Products covered | Solar PV cell models under ALMM List-II |
| Consultation deadline | 12 October 2026 |
| Technical institution involved | National Institute of Solar Energy (NISE) |
| Proposed transition | Two months from issuance of the final memorandum for specified existing or already-inspected models |
| Current status | Revised draft under consultation |
What Is ALMM List-II and Why Is It Important for Solar PV Cell Manufacturers?
ALMM stands for Approved List of Models and Manufacturers.
It is an MNRE framework used to identify solar equipment models and manufacturers that have been enlisted under the applicable procedures.
The purpose is to provide an official reference for solar equipment used in projects covered by the relevant ALMM requirements.
Being included in an ALMM list is different from merely manufacturing or selling a solar product. Enlistment depends on the requirements applicable to the relevant equipment category.
What Is ALMM List-II?
ALMM List-II covers solar photovoltaic cells and their manufacturers.
Solar cells are the individual electricity-generating units used inside many solar modules. A solar module contains interconnected cells that convert sunlight into electrical energy.
The inclusion of solar cell models in ALMM List-II helps identify manufacturers and products under the applicable MNRE framework.
The List-II requirements became applicable to specified solar projects from 1 June 2026, subject to the relevant orders, exemptions and transitional provisions.
Difference Between ALMM List-I and List-II
| Particular | ALMM List-I | ALMM List-II |
| Main equipment | Solar PV modules | Solar PV cells |
| Focus | Enlisted module models and manufacturers | Enlisted cell models and manufacturers |
| Product stage | Finished solar module | Solar cell used in module manufacturing |
| Relevance | Module eligibility under applicable ALMM conditions | Cell eligibility under applicable ALMM conditions |
| Revised October naming proposal | Not the direct subject | Directly concerned |
ALMM List-I(a) is also relevant to the distinction between module categories based on cell origin and the applicable Bill of Materials. Its treatment must be read with MNRE's separate orders governing that list.
The October proposal specifically addresses the naming of cell models in List-II, rather than introducing a new naming system for all solar modules.
Why Is Solar Cell Model Identification Important?
A solar cell model name helps businesses identify the product they are manufacturing, buying or using.
For example, procurement and technical teams may need to know whether a model uses TOPCon or Mono PERC technology, what wafer category it belongs to and which manufacturer supplies it.
When companies use very different model naming practices, these details may not be immediately apparent.
A common naming format would make some of this information visible directly from the model identifier.
The Regulatory Framework for ALMM List-II in India
MNRE introduced the ALMM framework through its order dated 2 January 2019, followed by guidelines and subsequent amendments.
The framework has since developed through orders, clarifications and revisions relating to approved solar models and manufacturers.
For solar PV cells, MNRE issued provisions covering ALMM List-II and its implementation. The List-II framework is separate from, but connected to, the framework for solar modules.
- MNRE's Regulatory Role: MNRE issues the applicable ALMM orders, procedural requirements and official lists. It also publishes amendments and clarifications affecting the administration of the framework.
- Role of NISE: The National Institute of Solar Energy is involved in technical inspection arrangements connected with ALMM List-II enlistment.
The revised naming proposal expressly refers to NISE inspections, and coordination with manufacturers for model renaming.
How the October Proposal Fits into the Framework
The existing ALMM rules will remain in place. The October proposal focuses on how solar cell models under List-II are named with a fixed code for their technical details, and manufacturing origin.
This distinction matters. A manufacturer may already need to meet the applicable ALMM enlistment requirements. The revised nomenclature would change how its cell models are identified within that framework if the proposal is finalised.
Why Has MNRE Proposed a Standardised Naming System for Solar PV Cells?
MNRE has proposed a standardised naming system for solar PV cells to address differences in how manufacturers identify their products. The proposed format would make key technical details and manufacturing origins easier to identify, helping manufacturers, procurement teams and officials work with more consistent product records.
- Different Manufacturers Use Different Model Names
MNRE has observed that manufacturers currently follow their own naming methods.
These names may be suitable for internal product management but do not necessarily use the same structure to describe the product's technical characteristics.
A standard format would give manufacturers a common basis for identifying models.
- Technical Details Are Not Always Clear from Model Names
A product's name may not directly show its technology, wafer size, efficiency or manufacturing origin.
The revised system would include these characteristics in predefined character positions.
This means someone familiar with the coding system could interpret important details without relying entirely on proprietary naming conventions.
- Better Solar Cell Traceability
Solar cell manufacturing can involve several stages and different suppliers.
Polysilicon may be produced in one location, processed into an ingot elsewhere, converted into a wafer at another facility and finally manufactured into a solar cell in another country.
The proposed code would distinguish the domestic or foreign origin of these stages.
It would not, by itself, establish a complete supply chain verification system, but it could provide a useful common identifier for supporting records.
- Consistent Model Identification Across ALMM Records
The code could help maintain more uniform model records during technical inspection and enlistment.
It would also make it easier to connect model names with specific technical characteristics.
- Better Information for Solar Procurement
Solar module manufacturers and procurement teams often work with multiple cell suppliers.
A standard model identifier could help them compare product records and check whether the supplied models correspond to the technical details used in their procurement documents.
These are potential business benefits. The proposal does not guarantee that the new code will eliminate all verification or documentation requirements.
What Has Changed in MNRE's October 2026 Proposal?
The October 2026 draft revises the naming framework initially circulated on 3 August 2026.
Both proposals envisage a 14-character code, but they differ in the information represented by some of the characters.
The earlier proposal included provisions for identifying busbar-related characteristics and a manufacturer-specific identifier.
The revised October draft instead includes a three-character cell efficiency field and reserves the final three positions for future use.
The main changes are:
- Solar cell origin remains important: The code continues to identify the domestic or foreign origin of key manufacturing stages.
- Technology identification remains: Codes distinguish between different types of solar cells.
- Wafer-size identification remains: Manufacturers would use prescribed codes for wafer categories.
- Efficiency is now included: The revised proposal allocates three-character positions to cell efficiency.
- Busbar identification has been removed from the proposed code structure: It is no longer a separate field in the October version.
- The final three positions are reserved: These are not currently assigned to manufacturer-specific product information.
The changes appear intended to make the identifier more useful for describing the cell's manufacturing and performance characteristics.
August vs October 2026: Comparison of the Proposed Naming Systems
| Identification Area | August 2026 Proposal | October 2026 Revised Proposal |
| Overall code length | 14 characters | 14 characters |
| Manufacturing origin | Included | Retained |
| Solar cell technology | Included | Retained |
| Wafer size | Retained | |
| Busbar characteristics | Included | No separate field |
| Manufacturer-specific identifier | Included | No separate field |
| Solar cell efficiency | Not included in the same designated field | Three-character field added |
| Reserved positions | Earlier arrangement differed | Positions 12-14 reserved |
| Legal status | Earlier draft | Revised draft under consultation |
The October draft gives greater importance to cell efficiency, which is a measurable characteristic used to describe solar cell performance.
Manufacturers should compare their existing model records with the revised code structure. However, any mandatory changes should follow the final MNRE memorandum rather than assumptions made from the draft.
How Will MNRE's Proposed 14-Character ALMM List-II Code Work?
The revised proposal describes a common structure consisting of:
Manufacturer Brand Name + Space + 14-Character Alphanumeric Code
The manufacturer's brand name is separate from the 14-character code.
Each part of the code has a specified meaning.
Proposed Code Structure
| Character Position | Code | Information Represented |
| 1 | D/F | Polysilicon origin, or front-glass origin for thin-film technology |
| 2 | D/F | Ingot origin or equivalent process origin |
| 3 | D/F | Wafer origin or equivalent process origin |
| 4 | D/F | Solar cell manufacturing origin |
| 5-6 | MP/TC/HJ/BC/PS | Solar cell technology |
| 7-8 | MA/MB/GA/GB | Wafer size |
| 9-11 | Three numbers | Cell efficiency |
| 12-14 | XXX | Reserved positions |
The use of alphanumeric characters means the identifier contains both letters and numbers.
Positions 1-4: Origin of Polysilicon, Ingot, Wafer and Solar Cell
The first four characters show where different stages of production take place.
MNRE proposes two values:
- D- Domestic (Indian)
- F- Foreign
Each position relates to a different manufacturing stage.
Position 1: Polysilicon origin
Polysilicon is a highly purified form of silicon used in manufacturing many crystalline silicon solar cells.
The first character identifies whether the relevant polysilicon originated in India or outside India.
For thin-film technology, this field refers to the origin of the front glass instead.
Position 2: Ingot origin
An ingot is a solid block of silicon prepared for producing wafers.
This character identifies where the ingot was produced.
The draft also allows the relevant equivalent-process origin to be identified where applicable.
Position 3: Wafer origin
A wafer is a thin slice of semiconductor material used in solar cell production.
This character identifies the domestic or foreign origin of the wafer or equivalent manufacturing process.
Position 4: Cell origin
This position identifies whether the solar cell, or equivalent manufacturing process, was completed in India or outside India.
The draft specifically excludes cells manufactured using blue wafers from being treated as domestically manufactured cells.
The first four characters are particularly important because they distinguish material origin from final cell manufacturing origin.
Positions 5-6: Solar Cell Technology
The fifth and sixth characters identify the technology used.
| Code | Technology | Simple Explanation |
| MP | Mono PERC | Monocrystalline silicon cell technology using a passivated rear surface |
| TC | TOPCon | Tunnel Oxide Passivated Contact technology |
| HJ | HJT | Heterojunction technology combining crystalline silicon with thin-film semiconductor layers |
| BC | Back Contact | Cell design in which electrical contacts are located on the rear side |
| PS | Perovskite | Solar cell technology using perovskite-structured absorber materials |
- Mono PERC: This technology uses a specially treated rear surface to reduce electrical losses and improve cell performance.
- TOPCon: TOPCon uses a thin tunnel oxide layer and passivated contacts to reduce recombination losses. It is widely associated with high-efficiency crystalline silicon solar cells.
- HJT: Heterojunction cells combine different semiconductor layers to improve charge collection, and limit certain electrical losses.
- Back Contact: In this design, contacts are placed on the back of the cell, reducing shading from front-side metal contacts.
- Perovskite: Perovskite solar cells use a different class of light-absorbing materials and can be developed in various device structures.
MNRE's proposal allows additional technology codes to be incorporated as needed.
The listed codes describe cell technologies. They do not independently establish that a particular manufacturer's product has been approved.
Positions 7-8: Wafer Size Identification
The seventh and eighth characters describe the wafer category.
| Code | Wafer Category |
| MA | M10 |
| MB | M10R |
| GA | G12 |
| GB | G12R |
Wafer size matters because solar manufacturers produce cells using different wafer formats.
The relevant size can affect cell dimensions, production equipment compatibility and module design.
For example, M10 and G12 are recognised wafer-size families, while M10R and G12R refer to related rectangular formats.
The proposal uses short codes instead of writing the complete wafer category in every model identifier.
MNRE has also kept the possibility of introducing additional codes as technology and market requirements develop.
Positions 9-11: Solar Cell Efficiency
This is one of the important features of the revised October proposal.
Positions nine to eleven contain three digits representing the cell's percentage efficiency.
The decimal point is omitted, and the first three digits are retained.
| Actual Cell Efficiency | Proposed Efficiency Code |
| 24.67% | 246 |
| 25.55% | 255 |
| 25.67% | 256 |
| 24.55% | 245 |
The code does not provide the complete efficiency percentage.
For example, 24.67% becomes 246. Therefore, the coded identifier is not a substitute for full technical efficiency records.
Manufacturers would still need accurate underlying efficiency information for applicable testing, inspection and product documentation requirements.
Positions 12-14: Reserved Characters
The last three positions are reserved.
In its illustrations, MNRE represents these positions as xxx.
The draft does not assign them to another technical characteristic at present.
Businesses should therefore avoid treating these reserved characters as a free field for inserting unapproved internal information.
Any future use would depend on MNRE's applicable instructions.
How to Read the Complete Code
MNRE provides the following illustrations in the draft.
Illustration 1: ABC FDDDTCGB256xxx
| Code Component | Meaning |
| ABC | Manufacturer brand |
| F | Foreign polysilicon |
| D | Domestic ingot |
| D | Domestic wafer |
| D | Cell manufactured in India |
| TC | TOPCon |
| GB | G12R wafer |
| 256 | Cell efficiency of 25.67% |
| xxx | Reserved |
This illustration shows a solar cell manufactured in India using foreign-origin polysilicon, with domestic ingot and wafer production.
It uses TOPCon technology and the G12R wafer category.
Illustration 2: ABC FFFDMPMA245xxx
| Code Component | Meaning |
| ABC | Manufacturer brand |
| F | Foreign polysilicon |
| F | Foreign ingot |
| F | Foreign wafer |
| D | Cell manufactured in India |
| MP | Mono PERC |
| MA | M10 wafer |
| 245 | Cell efficiency of 24.55% |
| xxx | Reserved |
The second illustration is especially useful because it shows that imported upstream materials do not automatically mean the final cell was manufactured outside India.
However, eligibility for a project subject to domestic content requirements must be assessed under the relevant DCR provisions, not merely by reading the code.
How Will Domestic and Foreign Solar Cell Origins Be Identified?
A solar cell passes through several manufacturing stages before becoming part of a module.
These stages may take place within one country or across several countries.
The proposed code identifies four separate origin points rather than using only one country-of-origin description.
- Domestic Polysilicon: The first character would be D when the relevant polysilicon is of domestic origin. This information describes an upstream manufacturing input.
- Imported Polysilicon: The first character would be F for foreign-origin polysilicon. It does not automatically mean that the subsequent ingot, wafer or cell is foreign-manufactured.
- Domestic Ingot and Wafer Manufacturing: Positions two and three would separately identify ingot and wafer origin. This allows the identifier to distinguish between imported starting materials and subsequent manufacturing activity in India.
- Final Solar Cell Manufacturing: Position four identifies the country where the solar cell is manufactured. It helps distinguish cells made in India from those produced in other countries.
However, the draft contains a specific condition concerning blue wafers, which must also be considered.
Why This Matters for Manufacturers
The proposed format could make it easier for businesses to describe supply chain origin consistently.
Manufacturers may need to maintain reliable records to support the origin classifications they declare.
A model code is useful for identification, but it does not replace the supporting evidence needed under applicable regulatory or procurement requirements.
Will Solar Cells Made Using Imported Blue Wafers Be Treated as Domestically Manufactured?
The October draft expressly states that a solar cell manufactured using a blue wafer, also known as a diffused silicon wafer, will not be treated as a domestically manufactured solar cell.
What Is a Blue Wafer?
A blue wafer is a silicon wafer that has already undergone certain processing steps associated with solar cell production.
These may include junction formation and the application of an anti-reflective coating.
Because important parts of cell processing have already taken place, a blue wafer differs from a basic unprocessed silicon wafer.
Why Does This Distinction Matter?
The manufacturing origin of a cell cannot always be decided simply by identifying the location where the last production or assembly operation took place.
MNRE's draft makes a specific distinction for cells made using blue wafers.
Therefore, a manufacturer cannot automatically classify such a cell as domestically manufactured merely because certain later operations were performed in India.
Impact on Domestic Content Requirement Projects
For projects covered by applicable Domestic Content Requirement provisions, the meaning of domestic manufacturing is important.
A company may need to verify whether the cells it proposes to use satisfy the relevant project-specific origin conditions.
The nomenclature proposal helps describe manufacturing origins. It does not replace the separate DCR rules and clarifications governing eligibility.
Scope and Applicability of the Revised MNRE Proposal
The proposed nomenclature concerns solar PV cell models under ALMM List-II.
Its direct relevance lies with cell manufacturers and the model information used during inspections and enlistment.
| Stakeholder or Product | Relevance |
| Existing ALMM List-II solar cell manufacturers | Proposed renaming of affected models |
| Manufacturers whose inspections are completed | Proposed model nomenclature revision |
| New ALMM List-II applicants | Proposed naming convention for relevant future inspections |
| Solar PV module manufacturers | Indirect relevance through cell sourcing and Bill of Materials |
| Solar cell importers and suppliers | Potential need to align supplier model information |
| Solar EPC contractors | Possible procurement-documentation relevance |
| Solar project developers | Possible use in product identification and procurement verification |
| Unrelated renewable energy equipment | Not directly covered by this nomenclature proposal |
The draft does not say that every solar equipment manufacturer must register again.
Nor does it establish a general new licensing process for solar importers or EPC contractors.
Its main subject is the standardisation of solar cell model names within ALMM List-II.
What Will Be the Role of NISE in Implementing the Revised Naming System?
The National Institute of Solar Energy has a specific proposed role in the implementation process.
- Inspections for New ALMM List-II Applications: According to paragraph 5 of the draft, inspections carried out by NISE after issuance of the relevant memorandum would follow the prescribed nomenclature.
Model details verified during these inspections and recommended for enlistment would need to match the standard format.
- Models Already Inspected: Some solar PV cell models may have completed inspections before the final nomenclature is introduced.
The draft proposes that these models also be renamed within the specified transition period. This means the proposal is not limited to future models.
- Existing ALMM List-II Models: For already enlisted models, paragraph 6 proposes a two-month period for revising model nomenclature.
NISE would coordinate with the concerned manufacturers.
What This Means in Practice
Manufacturers may need to confirm that their existing technical information can support the proposed model-code fields.
However, the draft does not set out a complete separate filing procedure or fee schedule for model renaming.
Businesses should await the final memorandum and any related administrative instructions before assuming a particular application process is mandatory.
Proposed Implementation Timeline and Transition Period
The revised draft contains several important dates and proposed implementation events.
| Event | Date or Period | Status |
| Original nomenclature proposal | 3 August 2026 | Earlier consultation draft |
| Revised memorandum | 5 October 2026 | Issued for consultation |
| MNRE website listing | 6 October 2026 | Published notice |
| Deadline for additional comments | 12 October 2026 | Expressly stated |
| Final memorandum | Not yet specified in the revised draft | Pending |
| Application to new NISE inspections | After issuance of the relevant final memorandum | Proposed |
| Renaming of already-inspected or enlisted models | Within two months from issuance of the final memorandum | Proposed |
Is the New Naming System Already Mandatory?
The revised October document is a draft circulated for stakeholder comments.
Its annexure contains provisions describing how the nomenclature would operate after issuance of the memorandum.
These provisions should not be read as confirmation that the draft format was already mandatory on 5 or 6 October 2026.
When Would the Two-Month Transition Period Begin?
The proposed two-month period is linked to issuance of the final memorandum.
It is not automatically calculated from the date of the revised consultation draft.
Until the final memorandum is issued, the precise end date cannot be established from this proposal alone.
How Will the Proposal Affect Existing ALMM List-II Solar Cell Models?
One of the most important questions for manufacturers is whether existing model names would also have to change.
The draft proposes that they would.
Models Already Enlisted Under ALMM List-II
Models already appearing on the approved list would be brought into the standard naming format within the proposed transition period.
This could require changes to recorded model names even where the technical product itself has not changed.
Models Already Inspected by NISE
The proposal also covers manufacturers and cell models whose inspections have already been completed.
This is important because an inspected model may not yet have reached the same administrative stage as an already enlisted model.
The draft refers to both categories.
New Models
After the final memorandum takes effect, new NISE inspections would follow the prescribed naming convention.
Manufacturers preparing applications may therefore benefit from understanding the proposed structure in advance.
Possible Documentation Changes
Depending on the final procedure, manufacturers may need to review:
- Internal model master records
- Cell technology descriptions
- Wafer-size classifications
- Efficiency data
- Manufacturing-origin information
- Existing inspection records
- Supplier and procurement documents
These are preparation areas, not a list of additional statutory filings created by the draft.
How Will the Revised Nomenclature Relate to ALMM List-I and List-I(a) Solar Modules?
The revised proposal is concerned with solar cells, but the information may also help in identifying the cell origin used in solar modules.
A solar module's Bill of Materials (BoM) records its components, which can include the cells used in manufacturing.
MNRE states that the domestic or foreign origin of cells would support the distinction between relevant ALMM List-I and List-I(a) module categories based on the BoM.
Relevance for Module Manufacturers
Module manufacturers may source cells from different producers.
Clearer cell model identification could make it easier to connect the cell model listed in procurement documents with the product information held in technical records.
Separate BIS Module Model-Number Procedure
A separate MNRE procedure reported in October 2026 concerns country identification in BIS-registered solar module model numbers.
That arrangement uses a four-character country code to identify the countries associated with module and cell manufacturing.
It is separate from the 14-character ALMM List-II solar cell model code.
Businesses should not confuse the two systems or assume that compliance with one automatically satisfies the other.
How Will the Proposed Naming System Affect Solar PV Manufacturers and Other Businesses?
The proposal directly concerns cell model identification, but its practical effects may extend to several businesses involved in the solar supply chain.
Impact on Domestic Solar PV Cell Manufacturers
Domestic manufacturers are the most directly affected.
If the revised format becomes final, they may need to review existing model names and ensure that the prescribed code correctly represents their products.
This may involve coordination between production, quality assurance and regulatory teams.
Manufacturers using both domestic and imported materials would need particular care when identifying origin fields.
Impact on Foreign Solar Cell Manufacturers
Foreign manufacturers whose cell models are enlisted or proposed for enlistment under ALMM List-II may need to align their model names with the same format.
They may also need to provide consistent information to Indian customers about technology, wafer category and the origin of manufacturing stages.
Impact on Solar PV Module Manufacturers
Module manufacturers purchase cells and use them to produce finished modules.
A common cell identifier could help when matching supplier information with technical records and Bills of Materials.
If suppliers change model nomenclature, module manufacturers may need to update internal references so that product records remain consistent.
Impact on Solar Cell Importers and Suppliers
Businesses importing, or distributing solar cells may have to coordinate revised model identifiers with overseas and domestic suppliers.
This could affect quotation documents, product catalogues and procurement systems.
However, the draft does not independently prescribe a new import licence or customs approval.
Impact on EPC Contractors and Solar Project Developers
EPC contractors and developers may benefit from having clearer cell identifiers when checking product information.
This may be useful in projects where the origin and eligibility of solar equipment are relevant.
Actual procurement eligibility must still be checked against the applicable project conditions and ALMM provisions.
Stakeholder Impact Matrix
| Stakeholder | Potential Impact | Main Area to Review |
| Domestic cell manufacturers | Model renaming and origin classification | Product master records |
| Foreign cell manufacturers | Standard model identification | Supplier technical information |
| Module manufacturers | Matching cell codes with module records | BoM and procurement data |
| Solar cell suppliers | Updating model references | Catalogues and supply documents |
| EPC contractors | Product verification | Procurement specifications |
| Project developers | Consistent equipment identification | Project sourcing records |
| Compliance teams | Reviewing applicable requirements | Compliance teams Reviewing applicable requirements |
These effects are potential operational implications. They should not be interpreted as separate legal obligations unless confirmed in the final framework.
Benefits of Standardised Solar Cell Model Identification
The proposed naming system would make solar cell models easier to identify by giving key technical details and manufacturing stages a fixed place in the code. This could help manufacturers, buyers and inspection teams read model information in a consistent way.
- Greater Consistency Across Manufacturers: A common model-code structure would reduce differences caused by separate proprietary naming practices.
Although brand names would remain different, the following characters would have a standard meaning.
- Clearer Manufacturing-Origin Information: The proposed code separates the origin of polysilicon, ingot, wafer and final cell manufacturing. This provides more detail than a single general country-of-origin statement.
- Easier Technology Identification: A short technology code would show whether the cell belongs to categories such as Mono PERC, TOPCon or HJT.
This could assist technical and procurement teams in identifying products.
- Better Access to Wafer Information: The wafer-size field would identify the relevant wafer category using predefined characters.
This may help businesses maintain consistent model records.
- Improved Visibility of Efficiency Information: The inclusion of a three-digit efficiency code adds another technical characteristic directly to the identifier.
It would not replace full efficiency test data but could make broad model differentiation easier.
- Better Traceability: A common identifier could support matching models across manufacturer, inspection and supply chain records.
Its usefulness would depend on accurate underlying information.
Challenges and Cost Implications for Solar Manufacturers
The proposed system may improve consistency, but manufacturers could face some initial administrative work.
- Updating Existing Model Records: Companies with numerous models may need to review their product databases and identify the correct standard codes. This could take time, especially where older model records do not separately record all the proposed information.
- Collecting Manufacturing-Origin Information: A manufacturer may need to check upstream supplier records to determine the correct D or F classification for each stage. Businesses purchasing intermediate products from multiple suppliers could face additional record-review work.
- Aligning Product and Supplier Documentation: If model names change, differences may arise between current supplier documents, and newly recorded identifiers. Companies may need to maintain clear cross-references between old and revised names.
- Internal Systems and Team Coordination: Model information may appear in:
- Product catalogues
- Procurement systems
- Technical specification sheets
- Quality records
- Inspection records
- Internal manufacturing databases
Any changes would need to be managed carefully to avoid confusion.
Are Any New Fees Proposed?
The revised draft does not expressly specify a new fee for adopting the standardised nomenclature.
It also does not provide a cost estimate for renaming models.
Manufacturers should therefore distinguish possible internal administrative expenses from government-prescribed charges.
How Can Solar Manufacturers Submit Comments on MNRE's Revised Draft Proposal?
MNRE has invited additional comments and suggestions from stakeholders on the revised nomenclature.
The consultation gives manufacturers and other interested parties an opportunity to comment before the proposed framework is finalised.
Official consultation details:
| Particular | Details |
| Authority | MNRE |
| Memorandum date | 5 October 2026 |
| Deadline | 12 October 2026 |
| Submission method | |
| Official email | azmal.mnre@gov.in |
| Subject | Revised standardised nomenclature for Solar PV Cell Models under ALMM List-II |
What Can Stakeholders Review Before Submitting Comments?
Manufacturers may wish to examine whether:
- The origin fields can be supported by available production and supplier records.
- The technology categories cover their products.
- The wafer-size codes match the categories used in their operations.
- The efficiency coding approach is sufficiently clear.
- The reserved characters are adequately explained.
- The proposed transition period is practical for existing models.
These are suggested points for consideration, not a prescribed government feedback format.
Businesses should refer to the official draft when submitting their views.
What Businesses Should Do Next
Manufacturers should begin by understanding the proposal and identifying which parts may apply to their products.
There is no need to assume that every model must immediately be renamed while the revised draft is still under consultation.
- Review the MNRE Memorandum: Read the October 2026 Office Memorandum and its annexure. Pay particular attention to character positions, origin definitions, technology codes and the proposed treatment of existing models.
- Identify Existing ALMM List-II Models: Prepare an internal inventory of listed and already-inspected solar cell models. This can help identify which records may be affected if the final naming system follows the draft. Review Manufacturing-Origin Records: Check available records showing the origin of:
- Polysilicon
- Ingots
- Wafers
- Completed solar cells
Manufacturers should also pay attention to the draft's specific treatment of blue wafers.
- Check Technical Product Information: Review the technology, wafer category and efficiency information associated with each model. This could help reveal missing or inconsistent records before the final requirements are introduced.
- Evaluate Internal Model-Naming Systems: Businesses can assess whether their current systems would allow revised model codes to be recorded and tracked. Changes should remain consistent with the final official requirements.
- Review Stakeholder Feedback Requirements: Businesses with technical concerns should consider submitting comments by the consultation deadline.
- Monitor the Final MNRE Memorandum: The final document will determine the actual requirements, implementation arrangements and transition provisions. Manufacturers should not rely solely on the consultation draft when deciding future mandatory actions.
Compliance Readiness Checklist for Solar PV Cell Manufacturers
The following checklist is a practical internal review tool. It is not a separate statutory checklist issued by MNRE.
| Review Area | Recommended Action | Suggested Responsible Team |
| ALMM List-II model inventory | Identify existing and pending models | Compliance |
| Brand names | Review recorded manufacturer-brand information | Product management |
| Polysilicon origin | Check available origin records | Procurement |
| Ingot origin | Review manufacturing or supplier information | Procurement |
| Wafer origin | Verify relevant records | Quality / Procurement |
| Cell origin | Review manufacturing-stage information | Production / Compliance |
| Cell technology | Match products with proposed codes | Technical team |
| Wafer size | Confirm applicable categories | Production / Quality |
| Cell efficiency | Review recorded efficiency values | Quality |
| NISE inspection status | Identify inspected models | Compliance |
| Final memorandum | Track official MNRE publication | Regulatory team |
| Transition planning | Prepare an update plan if required | Compliance / Operations |
The main purpose of this review is to help businesses understand whether their product records could support a standard naming format.
Future Outlook for ALMM List-II Solar Cell Identification
The next step is MNRE's consideration of stakeholder feedback and any subsequent decision to issue a final nomenclature.
If the proposed format is adopted, it could make model identification more consistent across ALMM List-II records.
The technology and wafer-size fields may also need to accommodate future developments, as the draft itself allows additional codes.
For manufacturers, the most useful immediate action is to review the proposed structure, identify possible documentation gaps and monitor the final memorandum.
No final implementation date should be assumed until MNRE publishes the applicable instructions.
How Corpseed Can Help?
Solar cell manufacturers and related businesses may need assistance interpreting ALMM requirements, reviewing technical documentation and understanding how new regulatory instructions apply to their products.
Corpseed's solar PV compliance consulting services and relevant regulatory compliance services can support businesses in assessing their position under the applicable framework.
Relevant areas of assistance include:
- Regulatory applicability assessment: Reviewing whether particular solar products and activities fall within relevant ALMM requirements.
- ALMM compliance guidance: Helping manufacturers understand the applicable enlistment procedures and regulatory instructions.
- Technical documentation review: Reviewing product information relevant to model identification and applicable compliance records.
- Manufacturer compliance assessment: Identifying potential gaps between available records and applicable regulatory requirements.
- Solar product compliance services: Supporting businesses with relevant product compliance planning.
- Regulatory update interpretation: Explaining final MNRE notifications and changes affecting relevant manufacturers.
- Compliance documentation support: Helping businesses organise information needed for applicable procedures.
The precise scope of assistance depends on the manufacturer's products, project requirements and the final official provisions.
Businesses dealing with ALMM List-II solar cell models can seek professional solar PV compliance consulting services to review the relevant requirements and prepare their compliance documentation.
Key Takeaways
MNRE has proposed a revised standard naming format for solar PV cell models under ALMM List-II. The purpose is to make product characteristics easier to identify and improve traceability across the solar manufacturing supply chain.
The main points are:
- MNRE issued the draft on 5 October 2026 for stakeholder comments. It has not yet become a final requirement.
- Each model would carry the manufacturer's brand name followed by a 14-character alphanumeric code.
- The code would identify manufacturing origin, solar cell technology, wafer size and efficiency.
- The draft proposes a two-month transition period for specified existing and already-inspected models following issuance of the final memorandum.
- Stakeholder comments are invited until 12 October 2026.
Manufacturers should review the draft and prepare relevant product information, while waiting for MNRE's final directions before treating the proposed nomenclature as mandatory.
About the Author

Parul Bohral
Legal Content WriterParul Bohral, a BALLB graduate and experienced legal researcher and content writer with expertise in various legal areas, including corporate law and intellectual property. I have gained valuable experience in esteemed legal environments, where I have strengthened my research skills, allowing me to approach legal writing with precision and depth.
As a legal content writer, I am committed to delivering work that not only informs but also engages readers. By staying informed about the latest trends in content marketing and regulatory developments, I ensure that my writing remains sophisticated and meets industry standards. My dedication to thorough research enables me to craft content that is both insightful and impactful.

